Welcome to RennTech.org Community, Guest
There are many great features available to you once you register at RennTech.org
You are free to view posts here, but you must log in to reply to existing posts, or to start your own new topic. Like most online communities, there are costs involved to maintain a site like this - so we encourage our members to donate. All donations go to the costs operating and maintaining this site. We prefer that guests take part in our community and we offer a lot in return to those willing to join our corner of the Porsche world. This site is 99 percent member supported (less than 1 percent comes from advertising) - so please consider an annual donation to keep this site running.
Here are some of the features available - once you register at RennTech.org
- View Classified Ads
- DIY Tutorials
- Porsche TSB Listings (limited)
- VIN Decoder
- Special Offers
OBD II P-Codes
- Paint Codes
- Videos System
- View Reviews
- and get rid of this welcome message
It takes just a few minutes to register, and it's FREE
Contributing Members also get these additional benefits:
(you become a Contributing Member by donating money to the operation of this site)
- No ads - advertisements are removed
- Access the Contributors Only Forum
- Contributing Members Only Downloads
- Send attachments with PMs
- All image/file storage limits are substantially increased for all Contributing Members
- Option Codes Lookup
- VIN Option Lookups (limited)
2010 Carrera S 6M Cab 150k miles
TLDR: Dealer tells me the code is 2402 and Durametric returns 0024 with a description that matches the dealer.
I am getting screwey values when I look up actual values.
I try to clear codes and they don't seem to clear.
Has anyone else seen this?
I got CEL after about 1000 miles after replacing the catalytic converters myself. I pulled the codes with my Durametric and got:
0024 - DMTL Diagnosis module for tank leakage; pump drive rUpper limit exceeded
0010 - Intake camshaft driver
I took it to Porsche because I wrongly figured this was related to my cats. They pulled the codes and said the car was throwing 2402 and that the 0010 was in the system but had been there for a long time and was not relevant.
Now I had cleared that 0010 about a half dozen times so I thought it was fresh. It did not register at the time, but that means my reset did not work.
They said that it would cost $1,100 to replace the DM-TL and filter. It was very likely the right thing to do because they tried to actuate it and it would not spin.
As I have dropped about $14k on my Porsche habit in the last 30 months and my wife has had about enough of this, I paid the diagnostic fee and replace the parts myself (saving about $700).
Now my Durametric is still pulling the same codes plus a new one:
0014 which it says is No signal/communication
That code, like the 0024, is not in my copy of the Porsche 997 essential companion.
So when went to look at live values relevant to the DM-TL the Durametric was putting in some weird results. Percents or bars when the units should have been seconds.
Background: DM-TL is a complicated pump/sensor that determines that there are no leaks in the gas fume recycling system. It pulls low amps if there is a leak, so a high value means there is a problem with the pump or maybe a short.
“Thank you worked like a charm!!!! I have a foxwell, getting error codes 31 ignition circuit - side airbag , driver
and 21 ignition circuit, driver
no idea what to do. Horn works depending on its mood. “
Any suggestions would help. I’ve taken off the door panels and disconnected and reconnected the airbags.
Hello everyone! I’ve run into some electrical problems on my '08 Turbo and I’m stumped.... I've looked through a lot of Renntech posts and don't see any thing close.
First the panoramic roof and sunshade were opening and stopped about foot open. Maybe coincidence, it happened right when someone opened the door. I’ve checked practically every fuse even pulling the pano-roof control unit (back where the motors are located, and the circuit board looks okay. Then the instrument panel has started to act strange. The gear indicator shows that it is all gears at once, see the photo which is while it is in drive and moving. I can shut the car down and restart and the problem goes away. The time keeps changing randomly and the outside temperature is wrong. The button that opens the rear hatch that’s on the driver door has stopped working. Then my battery died, it was five years old so no surprise. After I replaced it the airbag indicator on the panel has lit up. I’ve tried to reset the instrument panel (Main Menu> Settings > Factory Reset) but it will not allow me to select “Reset”. I’ve also pulled the fuse several times to reset the panel but no change.
Today, I’ve connected my iCarSoft POR II diagnostic tool to the car.
The Airbag section says it “cannot connect to the ECU” so I can not reset the airbag light. There are YouTube videos of people using the tool on Cayenne’s (albeit on newer models) to reset it so I believe I can. The Panoramic roof says it does not have any DTC codes. The lift gate button on the driver door indicates it has appropriate voltage and no DTC codes. Also, no DTC codes for instrument panel, electrical system or DME I’m not sure this is related or not, I changed out the interior incandescent bulbs with LEDs. I now know that LED bulbs give off electromagnetic interference but seems remote. (as a side note, I found this out when I put LED bulbs on my garage door opener unit and it stopped receiving commands from the remotes – I had to get special bulbs from Amazon) Yesterday, I removed all the LEDs and went back to the old bulbs – no change.
Any ideas, suggestions or guesses?
FYI: The car is in Drive, "D" and is in motion.
By Michael hurta
Hi - 2002 996: Scoured the lists but can't find this particular cluster problem anywhere. In short, my salvage cluster shows a list of errors on start up but my original was fine.... Here's the details. My current cluster shows an intermittent airbag failure warning on the led screen followed by the idiot light. It usually occurs at start up, clears at the stalk and the idiot light remains on, but flickers on occasion. My mechanic had ruled out everything he could related to the airbag warnings and since he didn't have a spare cluster, couldn't swap to test for that. I personally purchased a salvage cluster, removed the battery terminals, installed it and it came to life (I'm also having to buy replacement connector housings because mine disintegrated). The problem is the info screen pretty much scrolled through a variety of issues like oil pressure feedback, temp feedback, fuel feedback, etc. The oil pressure gage was also unresponsive. I expected the odometer to be wrong, but didn't expect all the errors. I also started the car and while it ran, it did run rough, sputtered a bit. Do I have a bad salvaged cluster? Does the cluster need to be programmed (beside the odometer)?