Server Lease Renewal/Software Licenses
Our yearly server lease, software licenses, as well as hardware operating costs, ARE due Dec 6th, 2021. Our current donations have fallen far short of the funds we need to renew. Please remember the RennTech.org community is Member supported so please consider a donation to help... THANK YOU!
Welcome to RennTech.org Community, Guest
Hi everyone. My 2006 Boxster S suddenly started making a squealing noise. Noise goes away at higher RPM, only to come back at lower RPM and at idle. Not related to gear or clutching at all. Noise seems loudest at the rear of the car; I can hardly hear it inside with the windows closed. Is this a serpentine belt issue? Or the bearing of some engine accessory? I have 50,000 miles, and have already changed the serpentine belt once, around 4-5 years ago, just due to age of the car. I have not yet had the time to open up the engine compartment to look further. If it's a belt, then I would expect more noise from inside the cabin, would I not? I have attached a recording indicating the squeal going away when I rev the engine.
By Kevin Bryck
Okay this is REALLY specific.
The adjustable tension cable on the drivers side of my cabriolet disconnected at the top where it threads (8mm) into the top frame, not at the bottom where it snaps onto the ball.
The is a larger diameter (10mm?) clean smooth painted hole where the cable needs to thread in, which leads to the presumption that there was a nut on the back side?
Searched all over including removing driver's side rear 'door' panel and fishing around with a magnet but no loose nut found.
Looks like getting to back side of this frame casting would entail a major disassembly of the cabriolet top frame?
Also, what does this clip that goes over hydraulic cylinder do?
Right side clips is in place about halfway down length of cylinder.
Left side clip was down around the base of the shaft.
Replacing it where there appears to be a shiny spot looks like it would interfere with the cabriolet top potentiometer arm.
Right cable threaded into frame at top
Right cable threaded into frame at top
Missing cable location
Smooth clean painted hole in top frame where 8mm cable end is supposed to thread in
Left upper cable end with 8mm thread
By David MB
Help - i have a 2003 Boxter tiptronic s - in great shape other than a shrill loud noise like a Kazoo that only happens above 78mph - it sounds as iff coming from around the mirror area of the windscreen but then occasional sounds like its coming from the speaker area passenger side - that being said could be sound transference. Read a number of blogs about badly fitting windscreen so put tape over top rubber seal and body but still there - - as a say like a kazoo at 78mph with hard or soft top - absolutely driving me mad - any help gratefully received.
After 18yrs my convertible top has finally encountered its first issue. After using this forum (thank you!!) to figure out how to access all of the components (top was stuck in closed position), I found the root of my issue, a bad cable. However, as I was very carefully removing the cable from the transmission, the "clip" which is molded into the plastic cover cracked and is no longer functional (see image). Not really surprising on an 18yr old piece of plastic. The transmission works perfectly and I do not want to replace it, so I am looking for advice on any other ways that I can keep the cable properly engaged to the transmission. Please let me know if anyone else has encountered this and if there are any viable solutions. Thank you!
The convertible top on my '99 Boxster has been acting up for the past few years. Sometimes worked fine and other times wouldn't work at all. I had it looked at by my local shop and by my local Porsche service center. My local shop replaced the switch in the convertible top latch housing (a few years ago) and then the emergency break switch (a couple years ago). This didn't solve the problem. Then a couple of weeks ago the Porsche service center again replaced the emergency break switch, again not solving the problem. Over the past week or so the top had completely stopped working, but then this morning it was working again (intermittently). The tech at Porsche said that everything has been checked (relay, switches, etc.) so he suggests replacing the convertible top motor for approximately $2500. I'd appreciate insights from anyone that has been through this. I see quite a few posts re malfunctioning tops so any info will be helpful.